Determining Energy Savings Using Utility Bills: A Winning Method For ESCOS By John Avina At Isnare.com Ezine ArticlesIntroduction: Energy Savings Tracking MethodsAfter installing energy conservation measures (ECMs), Energy Service Companies (ESCOs) often determine the energy savings resulting from the project and present the savings results to their customers. A common way to calculate energy savings is to measure the flows of energy associated with the ECM, and then to apply spreadsheet calculations to determine savings. For example, a chiller retrofit would might require measurements of chilled water supply and return temperatures and kW. The benefit of this approach is that the ECM is isolated, and that only energy flows associated with the ECM itself are considered.This method is described as Option A or Option B in the International Performance Measurement and Verification Protocol (IPMVP). Table 1 presents the different options. Option A requires some measurement and allows for estimations of some parameters. Option B requires measurement of all parameters. In both options, calculations are done (typically in spreadsheets) to determine what energy savings. Option C uses utility bills to determine energy savings.Some ESCOs Have Limited OptionsThere are many situations where Option A or Option B (Metering and Calculating) is the best approach to measuring energy savings, however, some ESCOs insist upon only using Option A or Option B, when clearly Option C would be most appropriate. If the ESCO was a lighting contractor, then Option A should work in all cases. Spot measurements of fixtures before and after, agreed upon hours of operation, and simple calculations can be inserted into a spreadsheet that can calculate savings. The same spreadsheet can be used over and over. However, for ESCOs that offer a variety of different retrofits, it is necessary to be able to employ all options so that the best option can be selected for each individual job. Controls Retrofits, or retrofits to HVAC systems are typically excellent candidates for Option C.However there are drawbacks with metering and calculating savings and these can include:- Greater expense- Difficulties convincing the customer of the appropriateness and veracity of the method and savings numbers- Inability to handle interactive or many difficult ECMs.ESCOs that do not have the capacity to employ all options are at a disadvantage over those ESCOs that can employ them all. Specifically Lebron 9, we want to address those ESCOs that only employ Option A and Option B. These ESCOs may encounter the following problems due to their limited offerings:- Measurement and Verification costs can be greater, which lead to higher project costs, which can limit the energy projects that the ESCO can sell. The lack of Measurement and Verification options overall can make the ESCO less competitive, and hurt the financial performance of the ESCO.- Using Options A or B sometimes require the customer to understand and approve of complex energy calculations. These options are often difficult to explain to customers who insist upon seeing savings in their utility bills. Customer satisfaction can suffer if Option C is not made available to customers who want to see savings on their bills.- Options A and B cannot handle difficult ECMs. The methods used to determine savings are inaccurate, and make large assumptions that cannot be borne out if a third party consultant is hired to oversee the savings determination process.These issues are discussed in more detail below.Cost of Utility Bill Analysis vs. Metering and CalculatingMeasurement and Verification should cost between 1% and 15% of the project cost. Metering and calculating savings often has costs associated with labor and equipment. As many project configurations are different, projects typically require unique configurations of sensors, placements of sensors and savings calculations. On more complicated ECMs, only highly skilled energy professionals can determine which measurement devices should be applied, and to what components. Manipulating data, and finally creating spreadsheets with engineering calculations also requires skilled personnel who command high wages. Metering equipment also has a cost, and for many projects, metering equipment, or control points, have to be purchased, and remain on the job for years.Of course, there are cases where metering and calculating is the least expensive and the most desirable method. If an ESCO only provides a lighting retrofit, then measuring a selection of lighting fixtures before and after the retrofit, and producing a spreadsheet that determines savings is the best option.On the other hand, utility bill analysis is inexpensive. With specialized utility bill analysis software, clerical workers can create the Measurement and Verification analysis. Bills are entered, weather imported, a linear regression performed, and reports made. Capital need not be sunk into metering equipment or control points or into long hours of analysis and data manipulation. Typically for utility bill analysis, measurement and verification costs are a fraction of what costs for retrofit isolation savings are - ranging between 1 and 5% of project costs.Explaining Savings Numbers to CustomersCustomers understand utility bills. The reason they entered into an energy savings contract is often triggered by the desire to lower their energy bills. Retrofit Isolation methods do not address the customer’s utility bill. A project may be saving energy, but the utility bill may actually be increasing. Retrofit Isolation does not address this at all. ESCOs need to be responsive to customer’s needs, and this is done through communicating in a manner that the customer’s understand. They want to see the savings on their utility bills - this is a method they would trust.In addition, customers are sometimes mistrustful of energy service companies that provide savings numbers that the customer cannot understand. Although the calculations in the spreadsheet may appear perfectly reasonable to the energy analyst, to a customer who is not well-versed in math, the calculations may remain incomprehensible, and the customer is thereby required to trust the energy service company, sometimes leading to mistrust. Energy savings calculations should remain as simple as possible and explained in a manner that the customer can understand. This makes the customer’s job easier, and reassures the customer that the energy service company is acting in a truthful manner.For these reason, more and more customers ask for Measurement and Verification using utility bills.Difficult and Interactive Energy Conservation MeasuresFor many energy conservation measures, Retrofit Isolation is the best option. This would include lighting savings, savings from energy efficient motors, and from other non-weather dependent energy users.However it is very difficult or impossible to measure savings for some energy conservation measures. Still, some ESCOs insist on using Retrofit Isolation for these difficult measures. For example, engineering calculations can be made estimating the savings to be had by shutting down air handlers at night. But, assuming that the air handlers receive chilled water from a chilled water loop shared with other air handlers, how is one to measure energy savings? Fan savings are easy (assuming the unit is constant volume), but in order to calculate savings, several estimations need to be made, which result in an estimate of energy savings, just as accurate before the retrofit took place as after it took place. Suppose the unit is a VAV system, at what percentage would the fan have been running? Suppose the cooling coil and/or heating coil modulated to meet a changing supply air set point - how are the fan CFM, cooling and heating loads to be calculated if the unit is not running and measurements can not be made?Controls retrofits are difficult to measure and quantify directly. Usually, however, when a controls or commissioning measure is enacted, more than one item is adjusted, which further complicates an already difficult task. Suppose a partially working economizer was fixed, in addition to putting the fan on a variable speed drive, in addition to shutting off the air handler during unoccupied hours, and finally upgrading the chiller plant. Each of these measures would interfere with the savings calculations of the other. How can one calculate chiller savings, when the loads have changed so dramatically via the economizer, reduced hours and reduced air flow? This is a very difficult task, that most likely cannot be done with an acceptable degree of certainty.Complicated cases like this require utility bill analysis to measure and quantify savings. The procedure is very simple, inexpensive, and easy to explain relative to many Retrofit Isolation methods.Benefits of Utility Bill AnalysisThe benefits of utility bill analysis to calculate energy project savings are as follows:- Utility Bill Analysis, by its nature, is relatively simple, and does not require complicated engineering analysis.- Utility Bill Analysis is relatively inexpensive, as it requires less skilled workers, less time and no dedicated equipment.- Utility Bill Analysis provides savings numbers in a format and method that makes sense to the customer.- Utility Bill Analysis is the best method to handle complicated energy conservation projects, or projects which interact with each other, making assessment of individual measures impossible.- ESCOs can use the fact that energy savings is determined using the customers’ utility bills as a selling point.Utility Bill Analysis and Changes in WeatherUnfortunately, a simple comparison of pre-retrofit and post-retrofit utility bills is usually not an effective method to determine energy savings from ECMs. Weather varies from year to year, and affects the amount of heating or cooling energy usage, which can interfere with actual utility savings numbers. For a fair analysis, utility bills should be “corrected” for weather data, which results in a reasonable savings determination. Linear regression is applied to utility usage versus degree days to determine pre-retrofit utility usage patterns, which are then compared to post-retrofit utility usage to determine savings. Unfortunately, the scope of this paper is limited, and cannot present the method in detail. Weather-correcting for weather is easy, however, as specialized software, used by ESCOs around the world, simplifies the weather correction process and presents savings reports.Drawbacks of Utility Bill AnalysisFacilities may change their energy usage patterns, by installing more equipment, building additions, occupancy changes, etc. This upsets the existing utility bill comparison of pre-retrofit to post-retrofit usage. These changes need to be monitored and accounted for with Baseline Modifications.There is a certain amount of randomness in utility bill comparison. So many factors influence the amount of energy usage in any given month, and they cannot all be accounted for. As a result Jordan 4 2012, if you are trying to show savings that is less than 10% of the total electricity load, then the randomness in the bills may seriously interfere with the accuracy of your savings calculations.If you track savings by comparing utility bills, you will only be able to track total savings for a given meter, but you will not be able to separate out the savings for different Energy Conservation Measures (ECMs). For example, if you installed a lighting retrofit, an energy efficient chiller and a control system in a hospital, you will not be able to tell how much energy is being saved by the control system. Energy analysts try to do break out the savings for each ECM occasionally, but they are only making educated guesses.ConclusionWhen an ESCO approaches a performance contract Lebron 9 Sale, there are several measurement and verification options available. Those ESCOs that only have at their disposal a limited set of options are often spending too much money on measurement and verification, and therefore are held back from selling larger projects, and limit their own success.Customer satisfaction may suffer when ESCOs only offer Retrofit Isolation approaches to Measurement and Verification, as customers may want to see savings in their utility bills. ESCOs who refuse to speak in the same language or terms as the customer may suffer decreased customer satisfaction.Published At: Isnare.com Free Articles Directory - http://www.isnare.com/Permanent Link: http://www.isnare.com/?aid=394113&ca=FinancesDISCLAIMER: All information, content, and data in this article are sole opinions and/or findings of the individual user or organization that registered and submitted this article at Isnare.com without any fee. The article is strictly for educational or entertainment purposes only and should not be used in any way, implemented or applied without consultation from a professional. We at Isnare.com do not, in anyway, contribute or include our own findings, facts and opinions in any articles presented in this site. Publishing this article does not constitute Isnare.com’s support or sponsorship for this article. Isnare.com is an article publishing service. Please read our Terms of Service for more information.